-
×
Dynabrade 90405 1/8" W x 24" L 60 Grit A/O DynaCut Belt, 50/pack
50 × $0.85 -
×
Insize 1108-200CAL, 0-8" DIGITAL Caliper with ISO17025 Calibration Cert, 6928640377358
1 × $135.94 -
×
Insize 2424-E300, BORE GAGE FOR BLIND HOLES, 4.3-11.8", 6928640357169
1 × $4,105.85
-
×
Insize 6881-A4, GAGE BLOCK ACCESSORY, holder, 4-8", 6928640316029
1 × $373.24
-
×
Dynabrade 11395 Guide Wheel
1 × $39.90 -
×
Dynabrade 82489 6" Dia. x 100 Grit A/O Vacuum PSA Filmbac DynaCut Disc, 100/Pack
100 × $1.47 -
×
Insize 4707-100, MACHINIST SQUARE WITH WIDE BASE, 3.9x2.8", 6928640317972
1 × $24.53
-
×
Insize 3108-1, DIGITAL OUTSIDE MICROMETER, IP65, 0-1"/0-25mm, 6928640326929
1 × $163.28
-
×
Insize 2127-10, DIGITAL BORE GAGE (setting ring is not included), 6-10", 6974029771620
1 × $476.76
-
×
Insize 2121-51, DIGITAL INTERNAL CALIPER GAGES, 1.2-2.0"/30-50mm, 6928640392801
1 × $350.00
-
×
Insize 4112-BD149, INDIVIDUAL STEEL GAGE BLOCK, .149", grade AS-1, 6928640353260
1 × $26.25
-
×
Dynabrade 54705 Rotor/Vane Set
1 × $118.01 -
×
Insize IST-W850A, DIGITAL TORQUE WRENCH, 1504~7521in.lb/125.4~626.8ft.lb, 6928640326295
1 × $2,135.88
-
×
Dynabrade 39200 2" Type C, Roto Peen Flaps
1 × $70.53 -
×
Air Turbine Tools 2590SSV - 6mm Angle Hand Tool Series (Short Version, Front Exhaust), 30,000RPM, 35847
1 × $585.00 -
×
Insize 3351-175, HIGH PRECISION DIGITAL MICROMETERS/SNAP GAGE (with data interface), 150-175mm/6-7", 6940561966923
1 × $1,305.47
-
×
Insize 4190-21H32, CERAMIC STANDARD BALLS, 21/32", 6940561969825
1 × $32.51
-
×
Dynabrade 90268 3" W x 10-11/16" L 180 Grit A/O DynaCut Belt, 10/pack
10 × $3.71 -
×
Insize 3332-1, INDICATING MICROMETER, 0-1", 6928640327537
1 × $643.75
-
×
Dynabrade 90367 3/4" W x 34" L 60 Grit A/O DynaCut Belt, 50/pack
50 × $2.55 -
×
Insize IST-W500A, DIGITAL TORQUE WRENCH, 885~ 4424in.lb/73.7~368.7ft.lb, 6928640326288
1 × $1,724.63
Standard Abrasives 541150, Quick Change TS P.A.R.T. #10 Disc Mandrel, 5/8 in TA4 (PILOT), 7000121722
$27.68
Factory Stock, 7-10 Day Leadtime
Standard Abrasives Quick Change P.A.R.T. Disc Mandrel secures the Standard Abrasives Quick Change P.A.R.T. Disc to a rotary tool with a 5/8-inch collet assembly. These P.A.R.T. (Paint Anodized Removal Tool) Discs are used to clean and prep painted or corroded surfaces around holes prior to re-riveting or connecting a ground wire.
About the Quick Change P.A.R.T. Disc
The Standard Abrasives Quick Change P.A.R.T. Disc Mandrel is designed specifically for use with our Standard Abrasives Quick Change P.A.R.T. Discs. These discs are used to remove surface contaminants, paint or primer at electrical grounding contact points. The disc’s center hole diameter self-aligns so it will only clean the workpiece hole and maintain the anodized layer surrounding it. Plus, they’re available in a range of grades and sizes for your specific application.
Maximize the Value of Your 3M Power Tools
Engineered to work effectively with your 3M rotary tools, we design our accessories to perform to the highest standards, to allow you to do more, more cost-efficiently.
Quality Standard Abrasives Solutions for Industrial Applications
The Standard Abrasives brand has supplied quality abrasives to the metalworking industry for over 50 years. Customers rely on our broad offering of high performance products including coated, bonded, and non-woven abrasive lines.
