3M Screen Cloth Disc Hand Pad Goes Hand in Hand with 3M Screen Cloth Discs
3M Screen Cloth Disc Hand Pad goes hand in hand with 3M Screen Cloth Discs. Use die numbers 500GC (5? diameter with 2 tabs), 600JR (6? diameter with 2 tabs) and 800JM (8? diameter with 2 tabs) (sold separately). Mineral is adhered to both sides of 3M screen cloth discs, so when one side of the disc wears down the other may be used. While operators typically use these discs dry during hand sanding, the screen is water resistant and may be used with a lubricant if necessary.
Each disc features two tabs. The holder pad has two ?tacks? designed for these tabs. Operators simply pierce the tabs on the disc with the tacks on the hand pad to secure the disc in place. This easy and convenient attachment system eliminates the need for adhesive, which has two key benefits. First, it helps minimize the mess that adhesive can sometimes cause. Second, as one side of the disc is not sacrificed for adhesive, both sides may be used and the disc is put to optimal use.
A Remedy for Small Surface Imperfections
When eliminating surface imperfections, evenly-applied pressure and consistent finishes tend to be top concerns. With these goals in mind, we created the 3M Screen Cloth Disc Hand Pad. This abrasive accessory helps operators apply even pressure to their 3M screen cloth discs and, consequently, the substrate. With a hand strap attached to the back of the pad, the accessory is easy to use and provides access to workpiece areas that may be hard to reach with machines.
This hand pad is available in soft and medium densities. A medium density pad is firmer ? a good match for highlighting or leveling the surface to reveal high and low spots. A soft density pad is a good match for light scuffing of the substrate.
Prior to applying primer or paint, ridding the substrate of small imperfections is no easy task. We know that operators value a clean, polished look. The 3M Screen Cloth Disc Hand Pad was engineered to help them get there.

Standard Abrasives 718052, A/O Full Taper Cartridge Roll, 1/4 in x 1-1/2 in x 1/8 in 60, 7100103092
3M 72385, Scotch Box Sealing Tape 373, Blue, 48 mm x 50 m, 36/Case, 7100024277
Dynabrade 93252 8" Dia. x 1/2" Center Hole, 400 Grit, A/O, Arbor-Mount Sanding Star
Dynabrade 56106 5" Dia. Non-Vacuum Disc Pad, Vinyl-Face
Dynabrade 13505 Dynastraight Finishing Tool, 1 HP, Rear Exhaust, 3,400 RPM, 5/8"-11 Arbor
Dynabrade 56178 6" Dia. Vacuum Disc Pad, Vinyl-Face
Dynabrade 96005 - 1/4" Male Plug with 3/8" NPT Male Thread
Dynabrade 94897 Re-usable Compression Fitting Ass'y (for 8mm Hose)
Dynabrade 10843 DynaPen Reciprocating Tool, 14,000 SPM, 1/8" Collet
Dynabrade 11011 Idler Arm Assembly
Dynabrade 53533 Cone or Plug Grinder (Triple Extension)
Dynabrade 11477 Dynabelter Abrasive Belt Tool, Heavy-Duty
Dynabrade 98580 Motor Tune-Up Kit for National Detroit Sander Models
Dynabrade 90040 5" Dia. Foam, Flat Face Polishing Pad
Dynabrade 56316 3" x 4-1/4" Vacuum Dynabug II Disc Pad, Hook-Face, Short Nap
Dynabrade 39200 2" Type C, Roto Peen Flaps
Dynabrade 90614 3" W x 10-11/16" L 80 Grit A/O DynaCut Belt, 10/pack 
